harp tuner
An online harp tuner analyzes the sound captured by your microphone and shows whether a plucked string is flat, sharp, or in tune. Tune a pedal harp or lever harp directly in your browser with this free chromatic tuner: allow microphone access, pluck one string, and follow the indicator until it stays centered.
Before you begin, check the string chart supplied for your harp. Pedal harps and lever harps may have different base tunings, ranges, and string layouts, so the maker's chart is the safest reference for every note.
To tune your instrument, allow microphone access when your browser asks.
Reference frequency used for tuning
Your instrument is in tune. Start playing.
Once your instrument is in tune, continue with Metronaut’s interactive sheet music and professional accompaniments. Slow down the tempo, transpose a piece, repeat difficult passages in a loop and get feedback on whether you are playing the right notes.

How to read the harp tuner
The diagram compares the three main tuner states. Pluck one string, check the expected note on your harp's string chart, and adjust until the cursor stays centered.
Pluck one string
Pluck one string clearly and confirm that the displayed note matches the note shown for that string on your harp's chart. Dampen nearby strings so they do not ring in sympathy.Centered means in tune
The string is in tune when the cursor remains centered while the sound is steady.Cursor on the left: pitch too low
The string sounds lower than the target note. Tighten the matching tuning pin by a very small amount, then pluck again.Cursor on the right: pitch too high
The string sounds higher than the target note. Loosen the matching tuning pin slightly, then test the string again.Let the reading settle
Harp strings produce strong overtones, especially in the bass and treble. Pluck gently, wait for the display to stabilize, and mute other ringing strings when needed.
How to tune a harp with the online tuner
- 1
Check the harp's tuning chart
Find the string chart for your exact harp model before changing any pitch. It identifies the intended notes and range without adding unsafe tension to the instrument. - 2
Disengage levers or pedals
On a lever harp, disengage every sharping lever. On a pedal harp, place every pedal in its flat top position. These positions expose the base notes that should be tuned; follow the maker's instructions if your model specifies another setup. - 3
Prepare a clear signal
Choose a quiet room, keep the device microphone uncovered, and place it near the middle of the soundboard without touching the harp. Pluck one string gently and damp neighboring strings. - 4
Match the string and tuning pin
Trace the plucked string to its tuning pin, then fit the correct tuning key securely onto that pin. Confirm the displayed note before turning anything. - 5
Adjust in tiny steps
If the string is flat, tighten the pin slightly to raise the pitch. If it is sharp, loosen the pin slightly to lower it. Remove the key or relax your hand, pluck again, and repeat until the indicator stays centered. - 6
Continue through the harp
Work through the strings in a consistent order, following the repeating C-D-E-F-G-A-B pattern and the model's chart. Recheck the full range at the end because changing one string can slightly affect the others.
Harp string colors and tuning layout
Most pedal and lever harps repeat the seven note names C, D, E, F, G, A and B across several octaves. C strings are usually red, while F strings are usually blue or black. These colors help you find your place, but the manufacturer's string chart remains the authority for the exact range and base tuning of your harp.
Follow the note sequence and trace each string directly to its tuning pin before turning the key.
Pedal harp and lever harp setup
Pedal harp
Tune with all pedals in the flat top position. The base notes include flats, so compare each string with the pedal-harp chart supplied by the maker rather than assuming every string is natural.Lever harp
Tune with all levers disengaged. Many lever harps have a C-major base tuning, while fully levered models may instead be set up in E-flat or another maker-recommended tuning.Red C strings
Each red string marks C and begins another seven-note cycle, making it easier to navigate the range.Blue or black F strings
Each blue or black string marks F. The uncolored D, E, G, A and B strings sit between the colored reference strings.
Harp-specific tuning tips
Move the tuning pin very little
A small turn can change a harp string by a large interval. Make one tiny correction at a time and never force a pin or string that feels unusually resistant.Keep the key on the matching pin
It is easy to pluck one string while the key is fitted to a neighboring pin. Trace the string from soundboard to pin before every adjustment.Control sympathetic vibration
Other harp strings can ring with the note you pluck and confuse the microphone. Dampen the surrounding strings with your free hand when the display jumps.Give low and high strings time
Bass strings need time for the fundamental to settle, while the shortest treble strings respond best to a light pluck. Move the microphone closer if either end of the range is difficult to detect.Expect new strings to stretch
A new string or a new harp may need several tuning passes while the string and soundboard settle. Recheck more often after restringing, transport, or changes in temperature and humidity.Stop before causing damage
Do not raise a string above the pitch specified for the model. If a pin slips, a string looks damaged, or the harp resists normal adjustment, ask a teacher, harp technician, or the manufacturer for help.